Cables / Cable Assemblies

Angled shot of 2 4-pin JST SM Plug + Receptacle Cable.

4-pin JST SM Plug + Receptacle Cable Set

Product ID: 578

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector. They are good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming apart...

$1.50

3 in stock

2.1mm female/male barrel jack extension cable - 1.5m / 5 ft

Product ID: 327

This product is a 3-in-1 cable. By itself, it can act as an extension cord for any 5.5/2.1mm DC power cable. The heavy 24 AWG wires can handle up to 5A. You can also cut it half to make two barrel cables (one plug and one jack). This will allow you to connect a classic 'wall wart' to a breadboard or PCB without having to solder in a bulky power jack. Or you can use...

$2.95

In stock

Front shot of JST-PH Battery Extension Cable.

JST-PH Battery Extension Cable - 500mm

Product ID: 1131

By popular demand, we now have a handy extension cord for all of our JST PH-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH compatible socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but useful in...

$1.95

In stock

Waterproof Polarized 4-Wire Cable Set

Product ID: 744

Outdoor enthusiasts rejoice! We now have very useful 4-wire polarized cable sets in a waterproof variety. These cable sets are ideal for projects that must weather the weather: dust, water, rain, snow, tornado (not volcano proof!). Each cable has 4 color-coded conductors (red, black, white yellow) that match between the sides, for easy wiring and connectors are...

$2.50

In stock

Waterproof DC Power Cable Set - 5.5/2.1mm

Product ID: 743

Outdoor enthusiasts rejoice! We now have standard 5.5/2.1mm DC power cable sets in a waterproof variety. These cable sets are ideal for projects that must weather the weather: dust, water, rain, snow, tornado (not volcano proof!). They are a little bulkier than normal DC jacks because of the o-ring and removable over-screw. The o-ring is what makes the waterproof...

$2.50

In stock

6-conductor 0.1" socket-socket cable - 6" long

Product ID: 206

6" (150mm) long jumper cable of 6 conductors, 0.1" spacing with two 'female'/sockets on either end. Great for wiring up ShiftBrites together! Note: Wire colors may vary.

$1.75

In stock

Top view shot of a red and black JST PH 2-Pin Cable to Female Connector - 100mm.

JST PH 2-Pin Cable - Female Connector 100mm

Product ID: 261

Red and black tinned wires with a 2-pin JST PH connector on the end. 4" / 100mm long. Matches up nicely with our Lipoly chargers! We have the socket 'mating' version of this cable over here, as well as an 'extension' cable that has one of each soldered together. If you want a switch in the middle, try this switched extension cable. Finally, for PCB and breadboard...

$0.75

In stock

10-pin 2x5 Socket-Socket 1.27mm IDC Cable

10-pin 2x5 Socket-Socket 1.27mm IDC (SWD) Cable - 150mm long

Product ID: 1675

These little cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits, and have a few handy in our ARM-dev box. We thought you may want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is...

$2.95

In stock

Angled shot of 2 3-pin JST SM Plug + Receptacle Cable.

3-pin JST SM Plug + Receptacle Cable Set

Product ID: 1663

These 3-wire cables are 163mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 3 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

$1.50

In stock

10-pin Socket/Socket IDC cable - 6"

Product ID: 370

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

$2.00

41 in stock

6-pin Socket/Socket IDC cable - 6"

Product ID: 371

Connect this to that with an IDC cable! This cable has 6 pins (2x3) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto either side, they're quite sturdy!

$2.00

In stock

10-pin IDC Socket Rainbow ribbon to sockets Breakout Cable

10-pin IDC Socket Rainbow Breakout Cable

Product ID: 1199

We don't really know what to call this thing - it's got a 10 pin IDC cable on one end 6 inches of rainbow ribbon and tipped with 0.1" female socket connectors on the ends. We think this would be handy as a 10-pin JTAG breakout adapter, or maybe some sort of cable re-arranger. Anyhow, it seems useful and we picked up a bunch. Yeah we know it would be awesome if we...

$3.95

In stock

4-pin AT / ATX / IDE Molex to Berg Floppy Drive Power Cable

Product ID: 425

For big projects, with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. Only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use this...

$1.95

In stock

10-pin Socket/Socket IDC cable - Short 1.5"

Product ID: 556

Connect this to that with an IDC cable! This cable has 10 pins (2x5) in 0.1"x0.1" spacing. This is a shorter version of the cable we've carried for AVR programming, we use this for chaining together 16x24 LED matrix panels or GertBots About 1.5" long with two sockets crimped onto either side, they're quite sturdy!

$1.50

In stock

Angled shot of 2 6-pin JST SM Plug + Receptacle Cable.

6-pin JST SM Plug + Receptacle Cable Set

Product ID: 1665

These 6-wire cables are 162mm (6.4") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 6 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

$1.50

In stock

50-pin 0.5mm Pitch FPC Flex Cable - 250mm / 10" long

Product ID: 1682

FPC cables are super thin and flexible. They're often used in electronics when a a round cable would be too bulky, especially if you're dealing with 50 contacts like this one! This cable has 50 pins, 0.5mm pitch, and is 250mm long. It pairs well with our 50 pin 0.5mm pitch breakout board. 50-pin 0.5mm Pitch FPC Flex Cable - 250mm / 10" long (14:35)

$1.95

In stock

Angled shot of 2 5-pin JST SM Plug + Receptacle Cable.

5-pin JST SM Plug + Receptacle Cable Set

Product ID: 1664

These 5-wire cables are 168mm (6.6") long and come as a set. One cable has a JST SM type connector plug on the end. The other cable has a matching JST SM type receptacle connector. They are good for whenever you have 5 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from coming...

$1.50

90 in stock

Angled shot of 2 2-pin JST SM Plug + Receptacle Cable, socket type and plug type.

2-pin JST SM Plug + Receptacle Cable Set

Product ID: 2880

These 2-wire cables are 16cm long and come as a set. One side has a 2-pin JST SM type connector plug on the end. The other side has a matching 2-pin JST SM type receptacle connector. They are good for whenever you have 2 wires you want to be able to plug and unplug. We like the solid and compact nature of these connectors and the latch that keeps the cable from...

$0.75

In stock

STEMMA QT / Qwiic JST SH 4-Pin Cable - 50mm Long

Product ID: 4399

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board to the other....

$0.95

In stock

Top view of JST SH 4-pin to Premium Male Headers Cable next to US quarter for scale.

STEMMA QT / Qwiic JST SH 4-pin to Premium Male Headers Cable - 150mm Long

Product ID: 4209

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

$0.95

In stock

Angled shot of JST SH 4-pin Cable with Premium Female Sockets.

STEMMA QT / Qwiic JST SH 4-pin Cable with Premium Female Sockets - 150mm Long

Product ID: 4397

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

$0.95

In stock

JST PH 2-Pin Cable – Male Header 200mm

Product ID: 3814

For a really long time we assumed that the JST PH didn't have a free-hanging male header version. But then we found this JST-PH 2-pin Male Cable, and we were like, this is perfect! It's not a genuine JST connector, but it's 100% compatible with a nice clicky connection that you can undo without tearing the contacts from the housing. Plugs in nicely all with our...

$0.75

In stock

Angled shot of 100mm long 3-pin JST-SH cable with socket connectors.

JST SH 1mm Pitch 3 Pin to Socket Headers Cable - 100mm long

Product ID: 5765

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin connector, this cable will do the trick. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch socket connectors on the other. Note that the colors we got are somewhat matchy with our '2mm PH' sized STEMMA...

$1.50

In stock

JST-PH 2-pin Jumper Cable - 100mm long

Product ID: 4714

We use 2 pin JST PH connectors for all our battery packs, and if you want to put a board in series, like our LC709203F Stemma QT battery gauge, this cable will be very handy! Both ends have a JST PH 2mm pitch 2-pin plug. Between the two, 100mm of color coded wire - red for power, black for ground. No more soldering two pig-tails together! This is an A-A cable, that...

$0.95

In stock

1.25mm Pitch 2-pin Cable Matching Pair - 40cm long - Molex PicoBlade Compatible

Product ID: 4720

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. These cables are nice and long, 40cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

$0.95

In stock

Angled shot of 300mm long STEMMA QT cable

STEMMA QT / Qwiic JST SH 4-Pin Cable - 300mm long

Product ID: 5384

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

$1.25

In stock

Angled shot of STEMMA JST PH 3-Pin to Male Header Cable - 200mm.

STEMMA JST PH 2mm 3-Pin to Male Header Cable - 200mm

Product ID: 3893

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with female socket headers on the end For more information about JST PH...

$1.25

In stock

Angled shot of 150mm/6" long 4-Pin JST-PH Cable

STEMMA Cable - 4 Pin JST-PH 2mm Cable–Female/Female - 150mm/6" Long

Product ID: 3568

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-PH female 4-pin connectors on each end. These types of JST cables are commonly found on small rechargeable battery packs, RC receivers and transmitters, tiny cameras, and other small electronic devices We're using these to connect to STEMMA boards, the connector is compact yet durable, stays...

$0.75

In stock

Angled shot of STEMMA JST PH 4-Pin to Male Header Cable - 200mm.

JST PH 2mm 4-Pin to Male Header Cable - I2C STEMMA Cable - 200mm

Product ID: 3955

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" male header plugs on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has header pins, so it could be used to connect to socket...

$1.50

In stock

Angled shot of JST PH 3-pin Plug-Plug Cable - 100mm long.

JST PH 2mm 3-pin Plug-Plug Cable - 100mm long

Product ID: 4336

This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily. We're carrying these to match up with our STEMMA boards and sensors that have 3-pin connections - and the wires are even color coded! Red is power,...

$0.75

In stock

Angled shot of 20cm long 8-pin 2.54mm pitch cable.

2.54mm 0.1" Pitch 8-pin Jumper Cable - 20cm long

Product ID: 4939

These jumper cables are exactly what you need to connect common 0.1" header devices together. Sure you can tape together individual 1x1 header jumpers, but why not do it right? Use with perf-board, breadboards, breakouts, and more. You'll have a solid cable for quickly connecting any 2.54mm / 0.1" boards. Sometimes these connectors are called "Berg" or "Dupont" or...

$0.95

In stock

Angled shot of 4-pin JST PH to JST SH Cable.

4-pin JST PH to JST SH Cable - STEMMA to QT / Qwiic - 200mm long

Product ID: 4424

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

$0.95

In stock

Angel shot of the Grove to STEMMA QT / Qwiic / JST SH Cable

Grove to STEMMA QT / Qwiic / JST SH Cable - 100mm long

Product ID: 4528

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and a Grove connector on the other. This cable can be used with STEMMA or STEMMA QT / Qwiic boards to easily connect sensors and drivers from one board to the other. Please note you will have to watch for...

$1.95

In stock

Angled shot of a semi-coiled half-meter long JST-XH extension cable in red and black.

JST-XH Extension Cable - 2.5mm Pitch - 500mm long

Product ID: 5497

We now have a handy extension cord for JST-XH projects! One end has a JST-XH socket, and the other has a matching plug. Between the two, 500mm of color-coded wire. This solid 2.5mm pitch connector extension cable is great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. The two...

$1.25

In stock

Angled shot of STEMMA JST PH 3-Pin to Female Header Cable - 200mm.

STEMMA JST PH 2mm 3-Pin to Female Socket Cable - 200mm

Product ID: 3894

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" female header sockets on the end. We're carrying these to match up with our Hallowing, for extending and connecting sensors or LEDs - and the wires are even color coded! We also stock a version with male socket headers on the end For more information about JST PH...

$1.25

In stock

Angled shot of STEMMA JST PH 4-Pin to Female Header Cable - 200mm.

JST PH 2mm 4-Pin to Female Socket Cable - I2C STEMMA Cable - 200mm

Product ID: 3950

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with high-quality 0.1" female sockets on the end. We're carrying these to match up with any of our boards with 'STEMMA' connectors on them such as the Hallowing or Trellis M4. Can also be used with any STEMMA breakouts! This one has socket pins, so it could be used to connet to wires or...

$1.50

In stock

Molex PicoBlade 2-pin Cable - 200mm

Product ID: 3922

When 0.1" is too big, and JST PH's too chunky, the ultra-slim "PicoBlade" is a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection. This cable is nice and long, 200mm in fact. It's got both small form factor (won't take up a lot of real estate on your PCB) and friction lock to make easy-breezy connections to your HalloWing or anything...

$0.95

In stock

Angled shot of 2-pin cable matching pair.

2.5mm Pitch 2-pin Cable Matching Pair - JST XH compatible

Product ID: 4872

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock...

$0.95

In stock

Angled shot of 20cm long 2-pin 2.54mm pitch cable.

2.54mm 0.1" Pitch 2-pin Jumper Cable - 20cm long

Product ID: 4934

$0.75

In stock

Angled shot of 100mm long JST-GH 6-pin cable.

JST GH 1.25mm Pitch 6 Pin Cable - 100mm long

Product ID: 5754

This cable is a little over 100mm / 4" long and fitted with JST-GH compatible 6-pin connectors on either end. We dig the solid and compact nature of these connectors and the latch that keeps the cable from coming apart easily, and the wires are even color coded! These would go great with SEN54 or SEN55 all-in-one air quality sensor modules from Sensirion For more...

$0.95

In stock

Angled shot of JST PH 3-Pin Socket to Color Coded Cable - 200mm

JST PH 2mm 3-Pin Socket to Color Coded Cable - 200mm

Product ID: 4046

This cable will let you turn a JST PH 3-pin cable socket into 3 individual tinned wires. These are great to match up with our JST 3-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! We also carry the socket 'mating' version of this cable over here. For more information about JST PH connectors, visit the JST website

$0.95

In stock

Grove Cable Pigtail - 2mm pitch 100mm long

Product ID: 5244

If you'd like to make a connection to a board or breakout with Seeed Grove connection, this 100mm long 4-wire cable is fitted with a Grove connector and four bare wires. Please note you will have to watch for voltages on the power/signal pin when using 3V-only sensors, because Grove boards that are 5V logic like many Arduino UNO-compatibles. The colors are: Black for...

$0.95

In stock

Angled shot of JST PH 4-Pin Socket to Color Coded Cable - 200mm.

JST PH 2mm 4-Pin Socket to Color Coded Cable - 200mm

Product ID: 4045

This cable will let you turn a JST PH 3-pin cable socket into 4 individual tinned wires. These are great to match up with our JST 4-PH cables, for extending and connecting sensors or LEDs, and the wires are even color coded! Black for GND. Red for V+. White for SDA. Green for SCL. Even though this is a JST PH connector, it will fit into a Seeed Grove connector and...

$0.95

In stock

Angled shot of 20cm long 4-pin 2.54mm pitch cable.

2.54mm 0.1" Pitch 4-pin Jumper Cable - 20cm long

Product ID: 4936

$0.75

In stock

Angled shot of two 2.0mm pitch 3-pin JST PH matching cable pairs. The cables are not connected.

2.0mm Pitch 3-pin Cable Matching Pair - JST PH Compatible

Product ID: 5087

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 20 cm each, in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

$0.95

In stock

12 inch long, semi-coiled 10-pin 2x5 1.27mm pitch IDC Cable.

10-pin 2x5 Socket-Socket 1.27mm IDC (SWD) Cable - 300mm long

Product ID: 5804

These cables are handy when programming or debugging a tiny board that uses 10-pin 1.27mm (0.05") pitch SWD programming connectors. We see these connectors often on ARM Cortex dev kits and have a few handy in our ARM dev box. We thought you might want a backup cable as well, so now they are in the Adafruit shop! One cable per order. The ribbon cable is 0.06mm/0.025"...

$3.50

In stock

Angled shot of two 2.0mm pitch 5-pin matching cable pairs. The cables are not connected.

2.0mm Pitch 5-pin Cable Matching Pair - JST PH Compatible

Product ID: 5089

$0.95

In stock

Angled shot of 5-pin cable matching pair.

2.5mm Pitch 5-pin Cable Matching Pair - JST XH compatible

Product ID: 4875

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to...

$0.95

In stock

5-pin JST cable to 4-pin JST SH connect to a OLED Display and an Arduino.

5-pin JST ESLOV to 4-pin JST SH STEMMA QT / Qwiic Cable - 100mm long

Product ID: 4483

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT 4-pin JST SH on one end, and Arduino MKR (ESLOV) 5-pin JST SH connectors on the other, with the wires spun around so you can use it to connect STEMMA QT sensors we've got to any of the popular Arduino MKR boards! JST SH (also known as Qwiic)...

$1.50

84 in stock

Angled shot of 1.25mm pitch 2-pin 20cm long cable.

1.25mm Pitch 2-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4922

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection. This cable is handy and not too long, 20cm in fact. The friction lock makes easy-breezy connections whenever you need light and small connectivity. Note that this cable is 1:1 'symmetric' type...

$0.75

71 in stock

GPIO Ribbon Cable 2x8 IDC Cable - 16 pins 12" long

Product ID: 4170

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Comes in a classic Adafruit Black, has a nice soft flexible 16-line 0.05" ribbon cable and keyed IDC connectors on both ends. It's perfect for use with our GPIO Expander bonnet or with any of our RGB LED Matrices if you want to chain them together or...

$1.95

In stock

1.25mm Pitch 4-pin Cable Matching Pair - 40cm long - Molex PicoBlade Compatible

Product ID: 4722

$0.95

In stock

1.25mm Pitch 3-pin Cable Matching Pair - 40cm long - Molex PicoBlade Compatible

Product ID: 4721

$0.95

In stock

Angled shot of 1.25mm pitch 5-pin 20cm long cable.

1.25mm Pitch 5-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4925

$0.95

In stock

Top view shot of JST 2-pin Extension Cable with On/Off Switch.

JST 2-pin Extension Cable with On/Off Switch - JST PH2

Product ID: 3064

By popular request - we now have a way you can turn on-and-off Lithium Polymer batteries without unplugging them. This PH2 Female/Male JST 2-pin Extension Cable comes with an in-line Switch - click once to turn on, click again to turn off. It's super handy especially in tandem with our JST-terminated battery packs or LiIon & LiPoly batteries/accessories/chargers!...

$2.95

In stock

2.5mm Pitch 6-pin Cable Matching Pair - JST XH compatible

Product ID: 4876

$1.25

In stock

Angled shot of JST PH 3-pin Plug to Color Coded Alligator Clips Cable.

JST PH 2mm 3-pin Plug to Color Coded Alligator Clips Cable

Product ID: 4030

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 3-pin 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. This cable has a JST PH 3-pin on one side and alligator clips on the other, so it could be used to connect...

$1.95

In stock

Angled shot of 20cm long 5-pin 2.54mm pitch cable.

2.54mm 0.1" Pitch 5-pin Jumper Cable - 20cm long

Product ID: 4937

$0.95

In stock

100W Type C charging cable black magnetic

Black Woven USB A or Type-C to Type-C Cable with Magnetic Tip - 1 meter long

Product ID: 5520

Some days we're feeling extra fancy here at the 'fruit warehouse, and we have a big soft spot for woven fabric cables. Like, peep this fully reversible pink/purple Blinka-inspired cable or this mithril-like 3-in-1 Sync and Charge cable. Our latest addition to the collection is this 1 meter long Black Magnetic USB A or USB C to USB C Cable with a Magnetic Type C tip!...

$13.95

99 in stock

Angled shot of 20cm long 3-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 3-pin Jumper Cable - 20cm long

Product ID: 4935

$0.75

In stock

Angled shot of two 20cm long 6-pin matching cables almost connected.

1.25mm Pitch 6-pin Cable Matching Pair - 10 cm long - Molex PicoBlade Compatible

Product ID: 4986

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy connections...

$0.95

In stock

Angled shot of 12" long GPIO 2x10 IDC ribbon cable.

GPIO Ribbon Cable 2x10 IDC Cable - 20 pins 12" long

Product ID: 5294

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Has a nice soft flexible 20-line 0.05" ribbon cable and keyed IDC connectors. Good for JTAG connections, in particular - but is useful for anything really. This cable is 12" long and has 20 pins (2x10) in 0.1" x 0.1" spacing and two sockets crimped on...

$1.95

In stock

Angled shot of two separate JST-PH 2.00mm Pitch 6-pin Matching Pair Cables - 40cm long.

2.0mm Pitch 6-pin Cable Matching Pair - JST PH Compatible

Product ID: 5090

$0.95

In stock

Angled shot of 4-pin cable matching pair.

2.5mm Pitch 4-pin Cable Matching Pair - JST XH compatible

Product ID: 4874

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible. These cables are nice and long, 20cm in fact. They've got both small form factor and are a matching set, with an inline socket and plug connector. The two friction lock to...

$0.95

In stock

Angled shot of two matching 8-pin 1.25mm pitch cable assemblies.

1.25mm Pitch 8-pin Cable Matching Pair - 10 cm long - Molex PicoBlade Compatible

Product ID: 4976

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect. These cables are nice and long, 10cm each, in fact. They've got both small form-factor and are a matching set, with an inline socket and plug connector. The two friction lock to make easy-breezy...

$1.25

In stock

Angled shot of 20cm long 10-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 10-pin Jumper Cable - 20cm long

Product ID: 4941

$1.25

In stock

Angled shot of 20cm long 1.25mm pitch 8-pin cable.

1.25mm Pitch 8-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4928

$1.25

In stock

Angled shot of 20cm long 20-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 20-pin Jumper Cable - 20cm long

Product ID: 4946

$1.95

In stock

Angled shot of two 2.0mm pitch 4-pin JST PH matching cable pairs. The cables are not connected.

2.0mm Pitch 4-pin Cable Matching Pair - JST PH Compatible

Product ID: 5088

$0.95

In stock

Angled shot of 1.25mm pitch 20cm long 4-pin cable.

1.25mm Pitch 4-pin Cable 20cm long 1:N Cable - Molex PicoBlade Compatible

Product ID: 4924

$0.95

In stock

Replacement 5V Power Cable for RGB LED Matrices

Product ID: 4767

Here's a handy power cable for the RGB LED Matrix Panels we carry. Easily plug into the back of your RGB matrix and insert or screw the power and ground cables onto either the Matrix Portal or the Matrix Bonnet, or whichever microcontroller-and-add-on you're using for your RGB Matrix project. Works with any/all RGB LED Matrices that are 'HUB75' style. Not for use...

$2.50

In stock

Flora Sewable 3-Pin JST Wiring Adapter

Product ID: 2566

This product's about as simple as a cup of lemonade on a hot summer day. And, like lemonade, it's just three components! This board is a sewable adapter with a 3-pin JST wiring adapter. It's a perfect way to add a simple link between things like our Flora NeoPixels and more complicated products like our NeoPixel Rings. There are three holes on the board that are...

$1.95

In stock

Angled shot of 20cm long 12-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 12-pin Jumper Cable - 20cm long

Product ID: 4942

$1.50

In stock

Angled shot of 3-pin cable matching pair.

2.5mm Pitch 3-pin Cable Matching Pair - JST XH Compatible

Product ID: 4873

$0.95

In stock

Angled shot of 20cm long 16-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 16-pin Jumper Cable - 20cm long

Product ID: 4944

$1.75

In stock

Angled shot of 20cm long 9-pin 2.54mm pitch cable.

2.54mm 0.1" Pitch 9-pin Jumper Cable - 20cm long

Product ID: 4940

$1.25

15 in stock

Angled shot of 20cm long 14-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 14-pin Jumper Cable - 20cm long

Product ID: 4943

$1.50

In stock

Arcade Button and Switch Quick-Connect Wires - 0.187" (10-pack)

Product ID: 3835

Quick connector wire sets make wiring up our arcade-style or metal buttons quicky-quick. Each wire comes as a 'pair' with two 0.187" quick-connects pre-crimped. The wires are terminated together in a JST 2.5mm 2-pin connector. This connector will fit in 0.1" headers, so it's breadboard compatible or you can stick two wires into the end. Of course, you can chop this...

$4.95

In stock

Angled shot of 20cm long 7-pin 2.54mm pitch cable.

2.54mm Pitch 7-pin Jumper Cable - 20cm long

Product ID: 4938

$0.95

In stock

Shrouded Servo to Alligator Clip Cable - 17cm long

Product ID: 5514

Stretch out your servo connections with this flexible servo to alligator clip cable. It has a 3-pin shrouded "male" connection to plug your servo into and then, 17cm later, three alligator clips - it even keeps the common red/black/white color coding for power/ground/signal as you'd expect! This cable is perfect for connecting a servo to something with clip-pads like...

$1.95

In stock

angled shot of coiled half-meter long black banana plug cable.

Retractable Stacking Banana Plug Cable - Black 0.5 meter long

Product ID: 5472

Why are bananas never lonely? Because they hang around in bunches! A lot of power supplies, multimeters, and other benchtop equipment use standard 4mm banana plugs to connect this-to-that. When you need more, we now stock them! These are handy stackable and retractable Banana Plug cables! The retracting plastic protection bit on the end will automagically disappear...

$4.95

In stock

Angled shot of 2 1.25mm pitch JST-XH 5-Pin 200mm matching cable pairs.

1.25mm Pitch 5-pin Cable Matching Pair 10 cm long - Molex PicoBlade Compatible

Product ID: 4975

$0.95

In stock

JST SH 9-Pin Cable - 100mm long

Product ID: 4350

This 9-pin cable is just about 100mm / 4" long and fitted with JST-SH female connectors on both ends. Compared with chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel and are easy to insert and remove. We got these especially for our fantastically spooky Adafruit MONSTER M4SK in case you'd like to split the mask in two and...

$1.95

99 in stock

Angled shot of 1.25mm pitch 20cm long 3-pin cable.

1.25mm Pitch 3-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4923

$0.95

In stock

A red 0.5meter long cable with retractable banana plugs.

Retractable Stacking Banana Plug Cable - Red 0.5 meter long

Product ID: 5471

$4.95

In stock

Angled shot of 1.25mm Pitch 6-pin Cable 20cm long.

1.25mm Pitch 6-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4926

$1.25

In stock

Angled shot of a 1 meter long OBD Plug (16-pin) to DE-9 (DB-9) Socket Adapter Cable.

OBD Plug (16-pin) to DE-9 (DB-9) Socket Adapter Cable - 1 meter long

Product ID: 4841

Not to be confused with ODB, OBD stands for On Board Diagnostics and is used for analyzing and diagnosing vehicles. It's the thing your mechanic plugs into to find out why you've got a blinking engine light. Technically, OBD uses CAN bus and, hey, whaddya know, we've got some CAN-capable microcontroller boards here at Adafruit so this OBD Plug (16-pin) to DE-9 (DB-9)...

$5.95

In stock

Angled shot of rainbow-colored 34-pin IDC ribbon cable.

Rainbow 34-pin Dual Row IDC Floppy Ribbon Cable - 30cm long

Product ID: 5453

Often used for floppy drives, 34 pin IDC cables have a 2x17 array of pins. This cable will let you connect one port to another with a festive rainbow design! Both ends have strain relief and keyed connectors. Perfect for retro archiving projects or whenever you have a 2x17 0.1" header on two sides of a board that need connecting.

$2.95

In stock

Angled shot of 20cm long 18-pin 2.54mm pitch jumper cable.

2.54mm 0.1" Pitch 18-pin Jumper Cable - 20cm long

Product ID: 4945

$1.75

In stock

Angled shot of 20cm long 1.25mm pitch 10-pin color-coded cable.

1.25mm Pitch 10-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4930

$1.25

60 in stock

Angled shot of JST PH 4-pin Plug to Color Coded Alligator Clips Cable.

JST PH 2mm 4-pin Plug to Color Coded Alligator Clips Cable

Product ID: 4029

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. We're carrying these to match up with any of our boards or breakouts with 'STEMMA' connectors on them such as the HalloWing or NeoTrellis M4. Can also be used with any STEMMA breakouts! This cable has a JST PH 4-pin on one side and alligator clips on the...

$2.50

In stock

24-pin eInk / ePaper Extension Cable connecting Featherwing to Tri-color display

24-pin eInk / ePaper Extension Cable 0.5mm Pitch - 25cm Long

Product ID: 4230

When you need more distance between you and your eInk display, use this 24-pin 0.5mm pitch FPC cable with an extender adapter to streeeeeeeeeetch it out. The cable is generic, but we recommend it for use with eInk because often folks want to mount the displays elsewhere. Just carefully pry open the connector on the eInk Friend, eInk Feather Friend, etc, and use this...

$1.50

29 in stock

angled shot of 30cm long 4-pin Molex cable.

IDE Molex 4 Pin Socket Cable - 30cm long

Product ID: 5365

For big projects with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. The only problem is that these supplies have connectors that only plug into motherboards or hard drives. That's where this cable comes in. It has a matching 4-pin Molex connector to the hard drive/CD-ROM power cables that come out of a power supply so you can use...

$0.95

In stock

Angled shot of 20cm long 1.25mm pitch color-coded 9-pin cable.

1.25mm Pitch 9-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4929

$1.25

In stock

2.5" SATA III to USB 3.0 Adapter Cable - 30cm long

Product ID: 5622

This 2.5" SATA III to USB 3.0 Adapter Cable allows you to connect a standard 2.5" hard drive (HDD or SSD) to your computer. SATA III is like, a souped-up electronic energy drink, letting you backup files with a data rate up to 6Gbps. It's perfect for adding mega-amounts of storage to your single board computer, like a Raspberry Pi or BeagleBone. Simply plug the drive...

$14.95

48 in stock

IDE Molex 4-pin Plug Cable - 30cm long

Product ID: 5391

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see these big 'Molex' connectors used to provide power. They are used to give 5V (red), 12V (yellow) and ground (black) and with this connector you can easily wire up your favorite power supply or bench-top power source. We also...

$0.95

In stock

Angled shot of 20cm long 1.25mm pitch 7-pin color-coded cable.

1.25mm Pitch 7-pin Cable 20cm long 1:1 Cable - Molex PicoBlade Compatible

Product ID: 4927

$1.25

In stock

Angled shot of 20cm long flex ribbon cable.

26-pin 1mm pitch FPC Flex Cable - 20cm long

Product ID: 5386

FPC cables are super thin and flexible. They're often used in electronics when a round cable would be too bulky, especially if you're dealing with 26 contacts like this one! This cable has 26 pins, 1mm pitch, and is 20cm long. We use it to connect to laptop floppy drives but you may have other uses for this cable! One could also cut it into a smaller number of pads...

$0.95

In stock

Angled shot of 2m long PlayStation extension cable.

PlayStation Extension Cable - Compatible with PS1 and 2 - 2 Meters

Product ID: 5773

Ostensibly this extension cord was originally designed to allow PlayStation game players to be able to sit across the room from their game system, but what we are using it for is to connect to PS controllers and accessories without soldering directly to cables or cutting the connectors off. Since the connector is proprietary, it isn't like you can get a socket or...

$4.95

25 in stock

Angled shot of Four 2-pin 0.1" Pig-Tail Cables.

Pig-Tail Cables - 0.1" 2-pin - 4 Pack

Product ID: 1003

You'll find these handy 2-pin 0.1" spacing pig-tails to be quite helpful when wiring up your project. The connector end snaps cleanly into 0.1" spaced header (and fits neatly side by side on 0.1" spacing as well). We think this would be especially useful when paired with our PWM driver breakout, to control 16 PWM LEDs that are wired, but there are probably a dozen...

Notify Me

$1.95

Out of stock

Notify Me

Angled shot of STEMMA QT / Qwiic JST SH 4-pin Cable.

STEMMA QT / Qwiic JST SH 4-pin Cable - 100mm Long

Product ID: 4210

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers from one board to the other....

Notify Me

$0.95

Out of stock

Notify Me

Angled shot of 400mm long STEMMA QT cable.

STEMMA QT / Qwiic JST SH 4-Pin Cable - 400mm long

Product ID: 5385

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

Notify Me

$1.50

Out of stock

Notify Me

Angled shot of JST SH 4-Pin Cable - 200mm Long.

STEMMA QT / Qwiic JST SH 4-Pin Cable - 200mm Long

Product ID: 4401

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board...

Notify Me

$1.25

Out of stock

Notify Me

angled shot of 100mm long JST-SH 3-pin cable with male headers.

JST SH Compatible 1mm Pitch 3 Pin to Premium Male Headers Cable - 100mm long

Product ID: 5755

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin connector, this cable will do the trick. It has a 1mm pitch JST SH connector on one end, and 0.1" pitch plug connectors on the other. Note that the colors we got are somewhat matchy with our '2mm PH' sized STEMMA cables,...

Notify Me

$1.50

Out of stock

Notify Me

Angled shot of 30cm long shrouded servo connector to male jumper cable connectors.

Shrouded Servo to Premium Male Jumper Wires Cable - 17cm long

Product ID: 5515

Stretch out your servo connections with this flexible servo to premium male header jumper cable. It has a 3-pin shrouded "male" connector to plug the servo into and then, 17cm later, three separated jumper wire ends that plug into a breadboard or some header. It's excellent for when you want to quickly and easily connect a servo to an existing dev board with sockets,...

Notify Me

$0.95

Out of stock

Notify Me

Top view of several different kinds of 2.54mm pitch Molex PicoBlades as jumper wires.

2.54mm 0.1" Pitch Jumper Cables in Various Widths - 20cm long

Product ID: 5070

More Info

In stock

More Info

Top view of various JST-SH cables of varying lengths and connectors.

JST-SH 4-pin STEMMA QT / Qwiic Cables in Various Lengths

Product ID: 4912

These cables can be used with Qwiic or STEMMA QT boards to easily connect sensors and drivers from one board to the other. This variety of cables gives you the option of breadboarding with headers, using capacitive touch with alligator clips, and more. Compared with the chunkier JST-PH, these are 1mm pitch instead of 2mm, but still have a nice latching feel, while...

More Info

In stock

More Info

Top view of four connected pairs of JST PH compatible cables.

2.0mm Pitch Cable Matching Pairs - JST PH Compatible

Product ID: 5161

More Info

In stock

More Info

2-pin JST-SM power wire with male connector and bare wires

2-pin JST SM In-line power wire connector (male)

Product ID: 319

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. This is the matching connector to the inverter. It is required to connect EL wire to the inverter! 0.1" (2.54mm) pitch...

More Info

Discontinued

More Info

2-pin JST-SM power wire with female connector and bare wires

2-pin JST SM In-line power wire connector (female)

Product ID: 318

If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly. One wire is marked with a white dashed line. You can't plug these in backwards. We use these mostly for EL wire. This is the same connector as is on the inverter. It's useful if you're making a...

More Info

Discontinued

More Info

Silicone Cicoil Wire Cable - 4-pin 24AWG

Product ID: 1437

Discontinued - you can grab Silicone Cover Stranded-Core Ribbon Cable - 4 Wires 1 Meter Long - 30 AWG Black instead! This supple, slippery silicone wire has 4 conductors, 24AWG each sealed in a full silicone casing. It's heavy duty so you can pass tons of current but soft and flexible so its good for wearables. We think this would be a good pair for our LED strips....

More Info

Discontinued

More Info

4-pin JST SM Receptacle Cable

Product ID: 579

This cable product is no longer sold individually. We now only have them in set pairs for the same price! Get them here. This 4-wire cable is 20cm long and has a JST SM type connector receptacle on the end. It mates with the JST SM plug cable and is good for whenever you have 4 wires you want to be able to plug and unplug. We like the solid and compact nature of...

More Info

Discontinued

More Info

Multifunction Basic Power Supply Test Line - Banana to Various

Product ID: 3523

Discontinued - you can grab Retractable Stacking Banana Plug Cable - Black 0.5 meter long instead! We're always digging around for various test lines to use with our power supply - whether we're checking current draw of our Feather, or trying out new LED samples. We picked up one of these and its so handy we use it all the time now. It's compact and has three of the...

More Info

Discontinued

More Info

RockBLOCK 9603 Accessory Cable

Product ID: 4529

The RockBLOCK 9603 Accessory Cable is terminated with a simple 10-pin Molex-style connector at one end and male jumper wires at the other. This accessory cable will help speed up your development time, meaning you no longer need to terminate and crimp your own connector for the RockBLOCK 9603. If you're going to connect the RockBLOCK 9603 to anything other than your...

More Info

Discontinued

More Info