32x32 RGB LED Matrix Panel - 5mm Pitch

Product ID: 2026
$34.95



Qty Discount
1-9 $34.95
10-99 $31.46
100+ $27.96

Description

Bring a little bit of Times Square into your home with this sweet 32 x 32 square RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory.

These are a lot like our 6mm Grid 32x32 RGB LED matrix panel, but The LEDs on this panel are also a little closer together (a 5mm grid) so you won’t have to stand as far away to appreciate it. They are made to look good indoors, even with a wide-angle view (160 degrees) and look great in ambient light.

These matrices have 1024 bright RGB LEDs arranged in a 32x32 grid on the front. On the back there is a PCB with two IDC connectors (one input, one output: in theory you can chain these together) and 12 16-bit latches that allow you to drive the display with a 1:16 scan rate.

These panels require 13 digital pins (6 bit data, 7 bit control) and a good 5V supply, up to 4A per panel. We suggest our 4A regulated 5V adapter and then connecting a 2.1mm jack. Please check out our tutorial for more details!

Comes with:

  • A single 32x32 RGB panel,
  • An IDC cable
  • A power cable

RAM & Processor Requirements

Keep in mind that these displays were designed to be driven by FPGAs or other high speed processors: they do not have built in PWM control of any kind. Instead, you're supposed to redraw the screen over and over to 'manually' PWM the whole thing.

You'll need about 1600 bytes of RAM to buffer the 12-bit color image. You cannot use this size panel with an Arduino UNO (ATmega328) or ATmega32u4 - you need a chip with more RAM! These displays are technically 'chainable' - connect one output to the next input - as long as you have the RAM and CPU to handle it

This display does best with a high speed, high RAM microcontroller like a SAMD21, SAMD51, ESP32, etc. 8-bit micros are going to struggle if they work at all. The good news is that the display is pre-white balanced with nice uniformity so if you turn on all the LEDs it's not a particularly tinted white.

Power Requirements

There's a lot of LEDs! You may need up to 4A per panel. We suggest our 4A regulated 5V adapter and then connecting a 2.1mm jack. Please check out our tutorials for more details!

Connection Requirements

These displays require 13 GPIO pins to control. You may have to use consecutive or special pins depending on the driver firmware. We'll be honest: folks who try to wire directly are usually not successful, its easy to get confused and misconnect. For that reason we strongly recommend a ready-to-go board or adapter that makes wiring as easy as plugging in the cables and powering with 5V

We've also got our great Protomatter library that works in Arduino and CircuitPython for quick usage of many chained matrices.

Please note! These panels are remainder stock from factories that make huge light boards. For that reason, the look and size might vary from batch to batch, even though the basic operation, codebase and tutorial is the same.

 

 

Technical Details

We have a full tutorial here!

  • Dimensions: approx. 160mm x 160mm x 14mm
  • Panel weight with IDC cables and power cables: 218.82g
  • 5V regulated power input, 4A max (all LEDs on)
  • Compatible with M3 mounting screws
  • 5V logic
  • 2000 mcd LEDs on 5mm pitch
  • 1/16 scan rate
  • Indoor display, wide visibility
  • Displays are 'chainable'

As of August 11, 2020 - We no longer include Magnetic Feet with this product

 

RoHS 2 2011 65 EU Compliant
RoHS 2 2015 863 EU Compliant

Learn

RGBMatrix creates brilliant light displays
Hundreds of pixels of eye-blasting LED glory!
Show the Pi's video output on a large RGB LED matrix display!
See All Guides