Arduino / Accessories

This is a cute, half-size breadboard with 400 tie points, good for small projects. It's 3.25" x 2.2" / 8.3cm x 5.5cm with a standard double-strip in the middle and two power rails on both sides. You can pull the power rails off easily to make the breadboard as thin as 1.4" (3.5cm). You can also "snap" these breadboards together, either way, to make longer and/or...

This is a really nice power supply. It's a switching DC supply so it's small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 9V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC...

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or other electronic projects) - it's ready to go out of the box! Battery & screw not included.

I found these high-quality battery clips. They're molded plastic so they won't tear like cheap clips, and they cover the battery terminals to prevent shorts. Comes with a 5.5mm/2.1mm center-positive barrel connector, assembled! Battery not included.

Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll want to pick up a bunch for your electronic projects. Comes with a 5.5/2.1mm barrel jack on one end an a plug on the other. In between is an in-line switch that is rated for 125V and 2Amps (its normally used for lamps, we...

By popular demand! We now have the plates from the ARDX available separately. Acrylic plate is engraved and cut here at the Adafruit factory. There are mounting holes for your Arduino and a space that fits a half sized breadboard very nicely. THIS DOES NOT FIT THE ARDUINO MEGA. Comes with: 3mm thick plastic plate with engravings. 2 x 4-40 3/8" machine screws for...

We have so many Internet-connected goodies in the shop, we figured it's time to carry a cable so you can easily connect them up! This cable is 10 feet long, black and has all 8 wires installed. Perfect for use with the BeagleBone, Arduino Uno Ethernet, Arduino Ethernet Shield, NETduino Plus, Patch Shield, PoE Injector cables, IoT Printer pack or any other...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Metro, Feather, Raspberry Pi or other dev-board or microcontroller Approximately 3 feet / 1 meter long

“How could something so simple be so useful?” We heard once that in the 4th millennium B.C. some guy asked the person who invented the wheel that question. The person who invented the wheel’s answer, we were told, was something like “well it’s not actually that simple - it required engineering and innovation and this thing called...

This cute 3.2″ × 2.1″ (82 × 53mm) solderless half-size breadboard has four bus lines and 30 rows of pins, our favorite size of solderless breadboard for projects. You get a whoppin' 400 tie points! Plug in a Feather or Metro Mini with the rest for sensors or buttons or even a little display. You can pull the power rails off easily to make the...

This is a really nice power supply. It's a switching DC supply so it's small and light and efficient. It is thin so it fits in power strips without blocking other outlets. The output is regulated so you'll get a steady 12V up to 1000mA (1 Amp) of current draw. 5.5mm/2.1mm barrel jack, positive tip. This supply is designed to work anywhere in the world, 100V-240V AC...

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it for sure with the Arduino UNO R3, Adafruit Metro and Adafruit Metro Express. It's clear so you can see all your onboard LEDs and silkscreen labels. There are four small screws you can use to affix the board and some bumpers that go on the bottom. We rather...

This is a cute half-size breadboard with an assortment of small jumper wires, great for prototyping. The breadboard is 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two power rails on both sides. Power rails can be pulled off easily to make the breadboard as thin as 1.4" (3.5cm). The jumper wires are pre-cut and bent in right angles at...

This simple but effective enclosure will fit any 'classic Arduino' shaped development board - we've tested it with the Arduino UNO R3, Adafruit Metro, and Adafruit Metro M4 Express. We rather like this case because it's low-profile enough that you can fit shields on top. There's even a flexi-nub for pressing the reset button! Best of all, it's LEGO brick compatible!...

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield goes onto your Arduino and provides a slim rechargeable power pack, with a built in battery charger as well as DC/DC booster. Compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due - basically any...

This is a tiny little breadboard... half the size of a half-size breadboard! As of Sep 8, 2022 - This Tiny breadboard has been updated to make plugging and un-plugging boards and headers a buttery-smooth operation. Updated design also includes a metal plate. The metal plate is used to stick the breadboard on for mechanical support, and to keep the paper on the bottom...

This is a preprogrammed Atmega328P chip, useful if you want to make your own Arduino-compatible or repair a damaged chip on an exisiting Arduino UNO, Duemilanove, Diecimila, or NG! This chip is programmed with 'ADAboot', my version of the bootloader that is "quick-start" NG/diecimila/duemilanove/UNO-compatible. This means that there is still a 5-second delay from...

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 feet / 1 meter long Color may vary!

A smaller-sized rechargeable battery pack for your Raspberry Pi or Raspberry Pi B+ (or Arduino, or Propeller, or anything else that works with 5V!). This pack is intended for providing power to an iPhone, cell phone, tablet, etc but we found it does a really good job of powering other miniature computers and micro-controllers. If you want more power we have a 4400mAh...

These stickers are a must for anyone making a breadboarded Arduino-compatible. They fit right on top of a DIP ATmega328 (or '168) chip, and clearly indicate every pin as it would be called in the Arduino IDE. No more looking up the datasheet or schematic! The stickers are made of a tough vinyl, usually used for bumper stickers, so they will not fade, scratch, or...

Discontinued - you can check these Arduino accessories instead! We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box! Here are all the details: Dimensions: 3.6" x 5" x 1.35". Injection molded ABS plastic. Enclosure is easy to machine, drill, cut and shape to what you need. Brass screw inserts (can be used and...

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in clear plastic, the future! Here are all the details: Dimensions: 3.6" x 5" x 1.35". Injection molded clear plastic. Enclosure is easy to machine, drill, cut and shape to what you need. Brass screw inserts (can be used and reused many times,...

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box now available in gray translucent plastic, the future! Here are all the details: Dimensions: 3.6" x 5" x 1.35". Injection molded gray translucent plastic. Enclosure is easy to machine, drill, cut and shape to what you need. Brass screw inserts (can be used and...

Need an easy-to-use but powerful control solution for more industrial-type projects? Get the controller that does exactly what you want in a sturdy, contained package. Combine Arduino simplicity, ESP8266 WiFi connectivity, and Digital Logger's experience and reliability to customize your own PLC for controlling industrial and robotics projects. Digital Loggers...