64x32 RGB LED Matrix - 6mm pitch
Qty | Discount |
---|---|
1-9 | $64.95 |
10-99 | $58.46 |
100+ | $51.96 |
Description
Bring a little bit of Times Square into your home with this sweet 64x32 square RGB LED matrix panel. These panels are normally used to make video walls, here in New York we see them on the sides of busses and bus stops, to display animations or short video clips. We thought they looked really cool so we picked up a few boxes of them from a factory.
This version is the 6mm pitch 64x32 RGB LED Matrix. Please note you cannot use an Arduino UNO to drive this size, its way too big! Use an Arduino Mega, Raspberry Pi, BBB or other device that can handle displaying to RGB matricies and has plenty of RAM.
This is a a lot like our 6mm Grid 32x32 RGB LED matrix panel, but it's twice as wide and looks really good from far way. If you are looking for a 64x32 matrix, but at a closer view range, check out our 3mm pitch, 4mm pitch, or 5mm pitch 64x32 RGB LED Matrices.
This matrix has 2048 bright RGB LEDs arranged in a 64x32 grid on the front. On the back there are two IDC connectors (one input, one output: in theory you can chain these together) and 12 16-bit latches that allow you to drive the display with a 1:16 scan rate.
These displays are technically 'chainable' - connect one output to the next input - but our Arduino example code does not support this (yet).
These panels require 13 digital pins (6 bit data, 7 bit control) and a good 5V supply, up to 4A per panel. We suggest our 4A regulated 5V adapter and then connecting a 2.1mm jack. Please check out our tutorial for more details!
Comes with:
- A single 64x32 RGB panel
- An IDC cable
- A plug in power cable
RAM & Processor Requirements
Keep in mind that these displays were designed to be driven by FPGAs or other high speed processors: they do not have built in PWM control of any kind. Instead, you're supposed to redraw the screen over and over to 'manually' PWM the whole thing.
You'll need about 1600 bytes of RAM to buffer the 12-bit color image. You cannot use this size panel with an Arduino UNO (ATmega328) or ATmega32u4 - you need a chip with more RAM! These displays are technically 'chainable' - connect one output to the next input - as long as you have the RAM and CPU to handle it
This display does best with a high speed, high RAM microcontroller like a SAMD21, SAMD51, ESP32, etc. 8-bit micros are going to struggle if they work at all. The good news is that the display is pre-white balanced with nice uniformity so if you turn on all the LEDs it's not a particularly tinted white.
Power Requirements
There's a lot of LEDs! You may need up to 4A per panel. We suggest our 4A regulated 5V adapter and then connecting a 2.1mm jack. Please check out our tutorials for more details!
Connection Requirements
These displays require 13 GPIO pins to control. You may have to use consecutive or special pins depending on the driver firmware. We'll be honest: folks who try to wire directly are usually not successful, its easy to get confused and misconnect. For that reason we strongly recommend a ready-to-go board or adapter that makes wiring as easy as plugging in the cables and powering with 5V
- We recommend the Matrix Portal ESP32-S3 for a WiFi-enabled powerful plug-and-play board
- The original Matrix Portal with SAMD51 is also a great plug-and-play board if you happen to want a Cortex M4 as a main processor (we recommend the S3 version, above, as it is faster and has more memory)
- For many Arduino-shaped boards, you may be able to use our RGB Matrix Shield (check the product page and tutorial for which Arduino-like boards can be used)
- We also have RGB Matrix FeatherWings for many Feather boards (check the product page and tutorial for which Feather boards can be used)
- For Raspberry Pi computers, our RGB Matrix Bonnet is fully plug-and-play for powerful Linux-controlled displays.
We've also got our great Protomatter library that works in Arduino and CircuitPython for quick usage of many chained matrices.
Please note! These panels are remainder stock from factories that make huge light boards. For that reason, the look and size might vary from batch to batch, even though the basic operation, codebase and tutorial is the same.
Please note:
- The back of the matrix will either be green or black
- This product may come with one or two power connections
- There may be a short coupling data cable installed in the center
Note: Shipping weight reflects UPS' new dimensional weight regulations.
Technical Details
- Dimensions: 385mm x 190mm x 13mm / 15.2” x 7.5” x 0.5”
- Panel weight with IDC cables and power cables: 544.31g
- 5V regulated power input, 4A max (with all LEDs on)
- Compatible with M3 mounting screws
- 5V logic level
- 1/16 scan rate
- Indoor display, 160 degree visibility
- Displays are 'chainable'
Revision History:
- As of December 2, 2020, we no longer include mounting screws or magnets.
Learn
![](http://cdn-learn.adafruit.com/guides/images/000/000/163/medium640/rgbmatrix.jpg)
-
Mouser Electronics
United States -
Digi-Key Electronics
United States -
TechMake Electronics
Mexico -
Paradisetronic.com
Germany -
BerryBase
Germany -
NTREX, Inc.- Devicemart
South Korea
See our Distributors page for a complete list of distributors.