Components & Parts / Audio/Sound

Drown out the voices in your head with a bone conduction transducer! This incredible speaker does not have a moving cone like most speakers you've seen, instead, a small metal rod is wrapped with the voice coil. When current is pulsed through the coil, the magnetic field causes a piece of metal to expand and contract - if pressed against a flat surface or cavity it...

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, connect one pin to ground (either one) and the other pin to a square wave out from a timer or microcontroller. For the loudest tones, stay around 4 KHz, but works quite well from 2KHz to 10KHz. For extra loudness, you can...

Add some extra boom to your audio project with these powered loudspeakers. We sampled half a dozen different models to find ones with a good frequency response, so you'll get quality audio output for music playback. Simply connect the standard 3.5mm stereo plug into your Raspberry Pi model B or B+, Wave shield, etc. There's even a volume control wheel on it so you...

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar/compatible with the...

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 4 ohm impedance and 3W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our class D amplifier board. Speaker - 3" Diameter - 4 Ohm 3 Watt (0:01)

Listen up! This high power 4" diameter speaker will amp up any audio project where you need loud sound! It is 4 ohm impedance, rated for 20W continuous power. (This thing is really loud) It also has four handy mounting tabs 3 inches apart, and a grill that fits on top. The grill is to protect the cones, and is not necessary for use. This speaker has a nice wide range...

Listen up! This 3" diameter speaker cone is the perfect addition to any audio project where you need an 8 ohm impedance and 1W or less of power. We particularly like this cone as it has 4 handy mounting tabs 60mm apart. Works great with our Wave shield or class D amplifier board. Speaker - 3" Diameter - 8 Ohm 1 Watt (0:01)

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very solidly into a breadboard, perma-proto or perf-board. Each order comes with one...

Hey want to hear a really loud noise? Apply 3V to 5V to this buzzer module and you'll be rewarded with a loud 2KHz BEEEEEEEEEEEEEEEEEP. Unlike a plain piezo, this buzzer does not need an AC signal. Inside is a piezo plus the driver circuitry that makes it oscillate at 2KHz. On one hand, that makes it really great for integrating into projects because you don't need...

This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a drum/crash sensor It's...

These earbud headphones are the perfect accessory for your FONA - they've been tested to work with our modules - but can be used with any iOS or Android device that uses a TRRS pinout. The buds themselves are 16mm in diameter with a nice 40" long. They come with a standard 4-pole TRRS headphone jack and have a small microphone for phone calls. We may change the model...

Hear the good news! This wee speaker is a great addition to any audio project where you need 8 ohm impedance and 1W or less of power. We particularly like this speaker as it is small and comes with nice skinny wires with a connector on the end. It has a handy "Molex PicoBlade" 1.25mm pitch 2-pin cable, which makes plugging into a board easy. Or you can cut off the...

Hear the good news! This speaker is a great addition to any audio project where you need a 4 Ohm impedance and 3W or less of power. At 40mm diameter it has a more square-ish shape, but a smaller face. Sound quality and volume are nicely sandwiched between our Thin Plastic Speaker with Wires and the honkin' 20W 4 Ohm Full Range Speaker. This bite-sized speaker comes...

Hey, listen up! It's the world's smallest USB microphone! OK maybe it's not in the Guinness Record Book, but it is pretty darn small! This plug-and-play Mini USB Microphone needs no driver, and its USB interface means you can use it with any computer, laptop, SBC, etc! Works great with a Raspberry Pi computer, but you can also use it with any other computer you want...

Add some crisp and compact audio to your project with this Mini External USB 2.0 Speaker. It's USB-only and does not require or use a 3.5mm audio jack. You'll get great audio, even with a device that doesn't have a head phone jack. And since it is powered over USB, there's no need to charge it by other means, merely plug it into your desired device's USB port and...

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many names, phone plug, phone jack, headphone jack, jack plug, etc. Used to transmit stereo audio signals, these connectors are a mainstay in audio equipment, especially speakers and microphones. For audio,...

One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") Stereo Audio Plug Terminal Block. It's the most common size...

Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. The pins are on 0.1" spacing so it plugs very solidly (and vertically!) into a...

This cable is easy to understand - you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It's also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It's also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection. Black wire connects to sleeve, white wire...

Listen up! This single 2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. This speaker does not come with a connector on the end, it's just plain bare wires! Works peachy-keen with any of our audio...

One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") 4-Pole (TRRS) Audio Plug Terminal Block. TRRS stands for Tip,...

One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") Stereo Audio Jack Terminal Block. It's the most common size...

This cable is easy to understand - you get a 3.5mm mono audio jack on one end, and two alligator clips on the other. It's also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It's also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection. Black wire connects to sleeve, white wire...

One truth about working with audio is you always need the cable or adapter you don't have in your toolbox. That's why we love these terminal-block audio connectors so much. No soldering required! Use stranded or solid core wire and a small screw driver to create custom wiring jigs. This is the 3.5mm (1/8") 4-Pole (TRRS) Audio Jack Terminal Block. TRRS stands for Tip,...

Here at the Adafruit factory, we're used to working within the confines of electrical resistance, and we never tire of a good "ΩMG!" or "Ω sweet Ω" play on words. Sometimes after a productive day of prototyping, testing, prepping, and shipping, we find ourselves in need of a healthy mental check-in and reset. Where are we going with this? Just wait!...

This large (30mm diameter) piezo element is nicely enclosed with mounting holes so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a...

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. Each jack comes with two solder eyelets and a panel mounting hex-nut. They made of...

Most modern headphone sets are purely digital - with three volume control buttons in-line with the cable. These headphones are interesting in that they have an analog volume control potentiometer. Perfect for use with electronic projects that don't have volume control, or for phones that don't know how to use the digital buttons. There is one button on the headset,...

The Andrea Superbeam Array-PA Microphone is a far-field, 2-microphone array with stereo output and superior quality and performance, designed for hearing and recognizing voices even in noisy environments. We tested it here in the Adafruit factory and it did a great job picking up our voice commands even when the machines were all running. The microphone is designed...