STEMMA / STEMMA QT (JST SH 1mm) / Cables and Connectors

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and STEMMA JST PH connectors on the other. You can sand down the center-nub key on the JST PH side to make it fit in a Grove connector. Chunkier JST PH connectors come with 2mm pitch, and JST SH (also...

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board to the other....

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT 4-pin JST SH on one end, and Arduino MKR (ESLOV) 5-pin JST SH connectors on the other, with the wires spun around so you can use it to connect STEMMA QT sensors we've got to any of the popular Arduino MKR boards! JST SH (also known as Qwiic)...

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one end, and a Grove connector on the other. This cable can be used with STEMMA or STEMMA QT / Qwiic boards to easily connect sensors and drivers from one board to the other. Please note you will have to watch for...

This cable will make it super easy to use our plug-and-play STEMMA QT boards with boards like Circuit Playground. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with grippy alligator clips. We're carrying these to match up with our boards or breakouts with 'STEMMA QT' connectors on them. This cable...

If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. This connector can be used with Qwiic boards and cables, to easily connect...

If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro 1mm pitch connectors that are JST SH compatible! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. These connectors can be used with Qwiic boards...

The SparkFun Qwiic or Stemma QT SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a 4-pin JST SH pin (Stemma QT or Qwiic) connector to your Raspberry Pi. The SHIM design allows you to plug directly to the Pi's I2C bus with no soldering required, and the thin PCB design allows for it to be sandwiched on your Pi GPIO with other bonnets or...

The SparkFun Qwiic HAT for Raspberry Pi is the quickest and easiest way to enter SparkFun’s Qwiic / STEMMA QT ecosystem when using that Raspberry Pi that you’ve come to know and love. The Qwiic HAT connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Raspberry Pi to an array of Qwiic connectors on the HAT. Since the Qwiic system allows for...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...

This cable will make it super easy to use our plug-and-play STEMMA QT boards and controllers with chips, breakouts, and other devices that are I2C compatible but don't come with a STEMMA QT socket already on 'em. On one end you get a Qwiic / STEMMA QT connector (technically known as a JST SH 4-pin plug) into 4 individual wires with 'micro hook' ends. The hooks are...

Qwiic, or STEMMA QT, is a very efficient way to quickly prototype an idea, but a lot of Qwiic/Stemma QT driver boards only have one port, and devices have two ports but that's only good for chaining. This Multiport board allows boards that have only one Stemma QT/Qwiic port to be added to the I2C bus. Or, use this hub to add as many I2C devices to the bus as you...

Here is the perfect hardware kit to make a RP2040 QT Trinkey into any kind of USB-connected smart sensor with a QT-sensor-sandwich! You can assemble it with just a plain Phillips screwdriver. Takes less than a minute to bolt on your favorite STEMMA QT or Qwiic board on top. And best of all, its stackable, so you could have multiple boards sandwiched on top of each...

These cables can be used with Qwiic or STEMMA QT boards to easily connect sensors and drivers from one board to the other. This variety of cables gives you the option of breadboarding with headers, using capacitive touch with alligator clips, and more. Compared with the chunkier JST-PH, these are 1mm pitch instead of 2mm, but still have a nice latching feel, while...

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers from one board to the other....

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic or STEMMA QT boards, to easily connect sensors and drivers from one board...

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch instead of 2mm, but still have a nice latching feel, while being easy to insert and remove. This cable can be used with Qwiic boards, to easily connect sensors and drivers to boards with 0.1" socket...